Kia Optima: Specification|
Engine |
T/M |
Joint type |
Max. permissible angle |
||
|
Outer |
Inner |
Outer |
Inner |
||
|
Gasoline 2.0 T-GDI |
A/T |
BJ#104 |
TJ#100 |
45° |
21° |
|
Gasoline 2.4 GDI |
M/T |
BJ#95 |
TJ#95 |
45° |
21° |
|
A/T |
BJ#95 |
TJ#95 |
45° |
21° |
|
| Tightening torque |
|
Item |
N.m |
kgf.m |
Ib.ft |
|
|
Front |
Wheel nut |
88.2 ~ 107.8 |
9.0 ~ 11.0 |
65.0 ~ 79.5 |
|
Driveshaft castle nut |
215.7 ~ 254.9 |
22.0 ~ 26.0 |
159.1 ~ 188.0 |
|
|
Strut assembly lower mounting bolt |
156.9 ~ 176.5 |
16.0 ~ 18.0 |
115.7 ~ 130.2 |
|
|
Brake caliper mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.8 ~ 72.3 |
|
|
Wheel speed sensor mounting bolt |
6.8 ~ 10.7 |
0.7 ~ 1.1 |
5.0 ~ 7.9 |
|
|
Brake disc mounting bolt |
4.9 ~ 5.8 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
|
Lower ball joint mounting bolt |
98.0 ~ 117.6 |
10.0 ~ 12.0 |
72.3 ~ 86.7 |
|
|
Tie rod end ball joint nut |
34.3 ~ 44.0 |
3.5 ~ 4.5 |
25.3 ~ 32.5 |
|
|
Rear |
Wheel nut |
88.2 ~ 107.8 |
9.0 ~ 11.0 |
65.0 ~ 79.5 |
|
Shock absorber upper mounting bolt |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
|
Shock absorber lower mounting nut |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
|
Brake caliper mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.8 ~ 72.3 |
|
|
Wheel speed sensor mounting bolt |
6.8 ~ 10.7 |
0.7 ~ 1.1 |
5.0 ~ 7.9 |
|
|
Brake disc mounting bolt |
4.9 ~ 5.8 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
|
Hub assembly mounting bolt |
78.4 ~ 88.2 |
8.0 ~ 9.0 |
57.8 ~ 65.0 |
|
|
Upper arm ball joint mounting nut |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
|
Lower arm mounting bolt |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
|
Assist arm ball joint mounting nut |
44.1 ~ 53.9 |
4.5 ~ 5.5 |
32.5 ~ 39.7 |
|
|
Trailing arm mounting bolt |
44.1 ~ 53.9 |
4.5 ~ 5.5 |
32.5 ~ 39.7 |
|
Specifications
LubricantsTire Rotation
To equalize tread wear, it is recommended that the tires be rotated every 7,500
miles (12000 km) or sooner if irregular wear develops.
During rotation, check the tires for correct balance.
When ro ...
Vehicle certification label
The vehicle certification label attatched
on the driver’s side center pillar gives the
vehicle identification number (VIN). ...
Compressor Oil. Repair procedures
Oil Specification
1.
The HFC-134a system requires
synthetic (PAG) compressor oil whereas the R-12 system requires mineral
compressor oil. The two oils must never be mixed.
...