Kia Optima: Tightening Torque Table Of Standard Parts - General Information - Kia Optima TF 2011-2024 Service ManualKia Optima: Tightening Torque Table Of Standard Parts

Bolt nominal diameter (mm)
Pitch (mm)
Torque Nm (kg.cm, lb.ft)
Head Mark 4
Head Mark 7

M5
0.8
3 ~ 4 (30 ~ 40, 2.2 ~ 2.9)
5 ~ 6 (50 ~ 60, 3.6 ~ 4.3)
M6
1.0
5 ~ 6 (50 ~ 50, 3.6 ~ 4.3)
9 ~ 11 (90 ~ 110, 6.5 ~ 8.0)
M8
1.25
12 ~ 15 (120 ~ 150, 9 ~ 11)
20 ~ 25 (200 ~ 250, 14.5 ~ 18.0 )
M10
1.25
25 ~ 30 (250 ~ 300, 18 ~ 22)
30 ~ 50 (300 ~ 500, 22 ~ 36)
M12
1.25
35 ~ 45 (350 ~ 450, 25 ~ 33)
60 ~ 80 (600 ~ 800, 43 ~ 58)
M14
1.5
75 ~ 85 (750 ~ 850, 54 ~ 61)
120 ~ 140 (1,200 ~ 1,400, 85 ~ 100)
M16
1.5
110 ~ 130 (1,100 ~ 1,300, 80 ~ 94)
180 ~ 210 (1,800 ~ 2,100, 130 ~ 150)
M18
1.5
160 ~ 180 (1,600 ~ 1,800, 116 ~ 130)
260 ~ 300 (2,600 ~ 3,000, 190 ~ 215)
M20
1.5
220 ~ 250 (2,200 ~ 2,500, 160 ~ 180)
360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
M22
1.5
290 ~ 330 (2,900 ~ 3,300, 210 ~ 240)
480 ~ 550 (4,800 ~ 5,500, 350 ~ 400)
M24
1.5
360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
610 ~ 700 (6,100 ~ 7,000, 440 ~ 505)

1. The torques shown in the table are standard values under the following conditions :
Nuts and bolts are made of galvanized steel bar.
Galvanized plain steel washers are inserted.
All nuts, bolts and plain washers are dry.
2. The torques shown in the table are not applicable :
When spring washers, toothed washers and the like are inserted.
If plastic parts are fastened.
If self-tapping screws or self-locking nuts are used.
If threads and surfaces are coated with oil.
3. Reduce the torque values to the indicated percentage of the standard value under the following conditions.
If spring washers are used : 85%
If threads and bearing surfaces are stained with oil : 85%
Emergency Towing
There are three popular methods of towing a vehicle : - The operator loads the vehicle on the back of truck. This is best way of transporting the vehicle. - The t ...

Meaning Of Symbols
There are five primary symbols used to complement illustrations. These symbols indicate the part to apply such materials during service. Symbol Meaning ...

See also:

Jack and tools
The spare tire, jack, jack handle and wheel lug nut wrench are stored in the luggage compartment. Remove the luggage under tray out of the way to reach the equipment. (1) Jack handle (2) ...

How to cancel automatic the outside (fresh) air position in the Floor, Floor- Defrost and Defrost position
When you select the Floor, Floor-Defrost or Defrost position, the system automatically turns on the outside (fresh) air position will be selected. If you don’t want the outside (fresh) air positi ...

Heating and air conditioning
1. Start the engine. 2. Set the mode to the desired position. To improve the effectiveness of heating and cooling : - Heating: - Cooling: 3. Set the temperature control to the desired position. ...

Copyright © www.kiopman.com 2024