Kia Optima: Adjustment
Glass Adjustment
| • |
Check the glass run channel
for damage or deterioration, and replace them if necessary. |
|
| 1. |
Remove the following parts:
| B. |
Front door quadrant inner
cover. |
|
| 2. |
Remove the glass mounting hole
plug (B). |
| 3. |
Carefully move the glass (A)
until the glass mounting bolts are visible, then loosen them.
|
| 4. |
Check that the glass moves smoothly. |
Door Position Adjustment
| • |
After installing the
door, check for a flush fit with the body, then check for equal
gaps between the front, rear, and bottom, door edges and the body.
Check that the door and body edges are parallel. Before adjusting,
replace the mounting bolts. |
|
| 1. |
Check that the door and body
edges are parallel.
|
| 2. |
Place the vehicle on a firm,
level surface when adjusting the doors. |
| 3. |
Adjust at the hinges (A) :
| A. |
Loosen the door mounting
bolts slightly, and move the door in or out until it aligns flush
with the body. |
| B. |
Loosen the hinge mounting
bolts slightly, and move the door backward or forward, up or down
as necessary to equalize the gaps. |
| C. |
Place a shop towel on
the jack to prevent damage to the door when adjusting the door. |
Tightening torque:(B) :
21.6 ~ 26.5 N.m (2.2 ~ 2.7 kgf.m, 15.9 ~ 19.5 lb-ft)
(C) : 34.3 ~ 41.2 N.m (3.5 ~ 4.2 kgf.m, 25.3 ~ 30.4 lb-ft)
|
|
| 4. |
Grease the pivot portions of
the hinges indicated. |
| 5. |
Check for water leaks. |
Door Striker Adjustment
Make sure the door latches securely without slamming it.
If necessary adjust the striker (A): The striker nuts are fixed. The striker can
be fine adjusted up or down, and in or out.
| 1. |
Loosen the screws (B) just enough
for the striker to move.
Tightening torque:(B) :
16.7 ~ 21.6 N.m (1.7 ~ 2.2 kgf.m, 12.3 ~ 15.9 lb-ft)
|
|
| 2. |
Tap on the striker with a plastic
hammer to adjust the striker. The striker will not move much, but will give
some adjustment. |
| 3. |
Hold the outer handle out, and
push the door against the body to be sure the striker allows a flush fit.
If the door latches properly, tighten the screws and recheck. |
Door Trim Replacement
•
Be careful not to scratch
the door trim and other parts.
•
Put ...
Components
1. Rear door trim
2. Rear door belt inside weatherstrip
3. Rear door trim seal
4. Rear door module
5. Rear door panel
6. Rear door side molding
7. Rear do ...
See also:
Inspection
Measuring Resistance
1.
Disconnect the cruise control switch connector from
the control switch.
2.
Measure resistance between terminals on the con ...
Components and Components Location
Components Location
1. Drive shaft
2. Lower arm
3. Front disk
4. Front strut assembly
5. Steering gearbox
6. Front stabilizer bar
7. Sub frame
...
Identification Number Description. Vehicle Identification Number
1.
World Manufacturer Identifier
(WMI)- KNA (Korea) : Passenger vehicle, MPV(Multipurpose
Passenger Vehicle)/SUV(Sports Utility Vehicle)/RV(Recreational Vehicle)
- 5XX (U. ...
Replacements
Rear Door. Components and Components Location