Kia Optima: Troubleshooting - RestraintKia Optima: Troubleshooting

Warning Lamp Activation
Warning Lamp Behavior after Ignition On
As soon as the operating voltage is applied to the SRSCM ignition input, the SRSCM activates the warning lamp for a LED lamp check.
The lamp shall turn on for 6 seconds during the initialization phase and be turned off afterward.
To alert the driver, the warning lamp shall turn on for 6 seconds and off for one second then on continuously after the operating voltage is applied if any active fault exists.
1.
Active fault or historical fault counter is greater or equal to 10.


2.
Normal or historical fault counter is less than 10.


3.
When turning the ignition switch ON during variant coding (EOL) mode, the airbag warning lamp is turned on and blinks at intervals of 1 second till the coding is completed.
If the variant coding is completed normally, the airbag warning lamp will turn on for 6 seconds, and then turned off. Otherwise the airbag warning lamp continuously blinks at intervals of 1 second.
(1)
In case the variant coding is normally completed


(2)
In case the variant coding is not completed


When there is active fault in airbag system or SRSCM internal fault, the variant coding (EOL) cannot be completed. In this case, perform the variant coding (EOL) procedure again after troubleshooting with the GDS.
SRSCM Independent Warning Lamp Activation
There are certain fault conditions in which the SRSCM cannot function and thus cannot control the operation of the standard warning lamp. In these cases, the standard warning lamp is directly activated by appropriate circuitry that operates independently of the SRSCM. These cases are:
1.
Loss of battery supply to the SRSCM : warning lamp turned on continuously.
2.
Loss of internal operating voltage : warning lamp turned on continuously.
3.
Loss of Microprocessor operation : warning lamp turned on continuously.
4.
SRSCM not connected : warning lamp turned on continuously.
Telltale Lamp Activation
The Telltale Lamp indicates the Passenger Airbag(PAB) enabled and disabled status based on occupant status of passenger seat. If the passenger seat is empty or occupied with child (or child seat), the Passenger Airbag is disabled and the Telltale Lamp is turned ON to inform the driver that the PAB is disabled. As soon as operating voltage is applied to the SRSCM ignition input, the SRSCM activates telltale lamp prove out. ODS (Occupant Detection System) will send an indeterminate status to the SRSCM as a default setting for passenger airbag deployment during the prove out period.
After ignition on, telltale lamp will turn on for 4 seconds and turn off for 3 seconds during the initialization phase and be turned NO afterward until receipt of valid enabled message from ODS system.

Component Replacement After Deployment

   
   
Before doing any SRS repairs, use the GDS Pro to check for DTCs. Refer to the Diagnostic Trouble Code list for repairing of the related DTCs. Check and repair all DTC''s before replacing a faulty or one whose airbag system has been deployed SRSCM.
When the front airbag(s) deployed after a collision, replace the following items. Make sure all DTC''s are repaired befor replacing with new SRSCM.
SRSCM
Deployed airbag(s)
Seat belt pretensioner(s)
Anchor pretensioner(s)
Front impact sensors
SRS wiring harnesses
Inspect the clock spring for heat damage.
If any damage found, replace the clock spring.
When the side/curtain airbag(s) deployed after a collision, replace the following items.
SRSCM
Deployed airbag(s)
Side impact sensor(s) for the deployed side(s)
SRS wiring harnesses
After the vehicle is completely repaired, confirm the SRS airbag system is OK.
Turn the ignition switch ON; the SRS indicator should come on for about six seconds and then go off.
General Information
Precautions General Precautions Please read the following precautions carefully before performing the airbag system service. Observe the instructions described in this manual, or the airbags c ...

Components and Components Location
Components 1. Driver Airbag (DAB)2. Steering Wheel3. Clock Spring4. Seat Belt Pretensioner (BPT)5. Pressure Side Impact Sensor (P-SIS)6. Side Impact Sensor (SIS)7. Side Airbag (SAB)8. Passenger A ...

See also:

Crankshaft Position Sensor (CKPS) Description and Operation
Description Crankshaft Position Sensor (CKPS) detects the crankshaft position and is one of the most important sensors of the engine control system. If there is no CKPS signal input, the engine ...

Specifications
Specifications DescriptionSpecificationsLimitGeneralTypeIn-line, DOHC?Number of cylinders4?Bore88mm (3.464in.)?Stroke97mm (3.819in.)?Total displacement2359cc (143.90cu.in)?Compression ratio13.0 ...

Power Out Side Mirror Switch Repair procedures
Inspection 1. Disconnect the negative (-) battery terminal. 2. Remove the front door trim panel. (Refer to the BD group - "Front door") 3. Disconnect the connector and remove the door mir ...

Copyright www.kiopman.com 2020