Kia Optima: Specifications - Driveshaft and axleKia Optima: Specifications

Specification
Engine
T/M
Joint type
Max. permissible angle
Outer
Inner
Outer
Inner
Gasoline 2.4
M/T
BJ#95
TJ#95
45°
21°
A/T
BJ#95
TJ#95
45°
21°

Tightening torque
Item
N.m
kgf.m
Ib.ft
Front
Wheel nut
88.2 ~ 107.8
9.0 ~ 11.0
65.0 ~ 79.5
Driveshaft castle nut
215.7 ~ 254.9
22.0 ~ 26.0
159.1 ~ 188.0
Strut assembly lower mounting bolt
156.9 ~ 176.5
16.0 ~ 18.0
115.7 ~ 130.2
Brake caliper mounting bolt
78.4 ~ 98.0
8.0 ~ 10.0
57.8 ~ 72.3
Wheel speed sensor mounting bolt
6.8 ~ 10.7
0.7 ~ 1.1
5.0 ~ 7.9
Brake disc mounting bolt
4.9 ~ 5.8
0.5 ~ 0.6
3.6 ~ 4.3
Lower ball joint mounting bolt
98.0 ~ 117.6
10.0 ~ 12.0
72.3 ~ 86.7
Tie rod end ball joint nut
34.3 ~ 44.0
3.5 ~ 4.5
25.3 ~ 32.5
Rear
Wheel nut
88.2 ~ 107.8
9.0 ~ 11.0
65.0 ~ 79.5
Shock absorber upper mounting bolt
49.0 ~ 63.7
5.0 ~ 6.5
36.2 ~ 47.0
Shock absorber lower mounting nut
137.2 ~ 156.9
14.0 ~ 16.0
101.2 ~ 115.7
Brake caliper mounting bolt
78.4 ~ 98.0
8.0 ~ 10.0
57.8 ~ 72.3
Wheel speed sensor mounting bolt
6.8 ~ 10.7
0.7 ~ 1.1
5.0 ~ 7.9
Brake disc mounting bolt
4.9 ~ 5.8
0.5 ~ 0.6
3.6 ~ 4.3
Hub assembly mounting bolt
58.8 ~ 68.6
6.0 ~ 7.0
43.3 ~ 50.6
Upper arm ball joint mounting nut
137.2 ~ 156.9
14.0 ~ 16.0
101.2 ~ 115.7
Lower arm mounting bolt
137.2 ~ 156.9
14.0 ~ 16.0
101.2 ~ 115.7
Assist arm ball joint mounting nut
78.5 ~ 88.3
8.0 ~ 9.0
57.9 ~ 65.1
Trailing arm mounting bolt
44.1 ~ 53.9
4.5 ~ 5.5
32.5 ~ 39.7

Lubricants
Engine
Lubricants
Quantity
Front driveshaft
BJ#95
GRB006 (UREA)
105g
TJ#95
SH06-VX21(UREA)
145g

High Voltage Shut-off Procedures
High Voltage Shut-off Procedures     Be sure to read and follow the “General Safety Information and Caution” before doing any work related with the high voltage sys ...

Special Service Tools
Special Service Tools Tool Name / NumberIllustrationDescriptionBand installer09495 - 39100Installation of hook type boot band.Band installer09495 - 3K000Installation of ear type boot bandLower ar ...

See also:

Closing the fuel filler lid
1. To install the cap, turn it clockwise until it clicks one time. This indicates that the cap is securely tightened. 2. Close the fuel filler lid and push it lightly and make sure that it is sec ...

Heater Unit Components and Components Location
Component Location Components 1. Heater Case (LH)2. Separator3. Evaporator Core4. Shower Duct5. Heater Core Cover6. Heater Core7. Mode Actuator8. Mode Cam9. Temp Actuator10. Vent Door Arm11. Fl ...

Inhibitor Switch Repair procedures
Inspection     • Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Power Circuit Insp ...

Copyright www.kiopman.com 2021