Kia Optima: Inhibitor Switch Repair procedures - Automatic Transaxle Control System - Automatic Transaxle SystemKia Optima: Inhibitor Switch Repair procedures

Inspection
   
   
Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage.
Power Circuit Inspection
1.
Disconnect the Inhibitor switch connector (A).
2.
Ignition KEY "ON" & Engine "OFF".
3.
Measure voltage between supplied power and ground at inhibitor circuit.

Specification Approx. 12V

Signal Circuit Inspection
1.
Connect the Inhibitor switch connector (A).
2.
Ignition KEY "ON" & Engine "OFF".
3.
Measure voltages between each terminal and chassis ground during shift lever changed "P, R, N, D".

Specification : See below "Signal Code Table"

Signal Code Table
PIN No.
P
P-R
R
R-N
N
N-D
D
Signal "1"
12V
12V
0
0
0
0
0
Signal "2"
0
12V
12V
12V
0
0
0
Signal "3"
0
0
0
12V
12V
12V
0
Signal "4"
0
0
0
0
0
12V
12V

Removal
   
   
Be sure to read and follow the “General Safety Information and Caution” before doing any work related with the high voltage system. Failure to follow the safety instructions may result in serious electrical injuries.
Be sure to shut off the high voltage circuit according to the “High Voltage Shut-off Procedures” before doing any work related with the high voltage system to avoid serious electrical injuries.
1.
Shut off the high voltage circuit.
( Refer to Automatic Transaxle System - "High Voltage Shut-off Procedure")
2.
Place the shift lever into the "N" position.
3.
Remove the under cover (A).


4.
Drain the coolant of hybrid motor cooling system.
( Refer to Hybrid Motor System - "Coolant")
5.
Remove the air duct (A).


6.
Remove the air cleaner assembly.
(1)
Disconnect the breather hose (A).
(2)
Disconnect the air intake hose (B) and then remove the air cleaner assembly (C).


7.
Remove the hybrid power control unit assembly.
( Refer to Hybrid Control System - "HPCU (Hybrid Power Control Unit)")
8.
Remove the tray (A).


9.
Remove the inhibitor switch (A).
10.
Remove the shift cable mounting nut (B).


11.
Remove the manual control lever (B) and the washer after removing a nut (A).


12.
Remove the inhibitor switch (A) after removing the bolts (2ea).

Installation


Installation
1.
Check that the shift lever is placed in the "N" position
2.
Install the inhibitor switch (A).
   
   
Lightly tighten the inhibitor switch mounting bolts so that necessary adjustments can be made.


3.
Install the manual control lever (A).
   
   
Lightly tighten the manual control lever nut (B) so that necessary adjustments can be made.


4.
Align the hole (A) in the manual control lever with the "N" position hole (B) of the inhibitor switch and then insert the SST inhibitor switch guide pin (09480-A3800).


5.
Tighten the nut (A) and bolts (B) with the specified torque.

Tightening torque:
A : 17.7 ~ 24.5 N.m (1.8 ~ 2.5 kgf.m, 13.0 ~ 18.1 lb-ft)
B : 9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)


6.
Remove the SST (09480-A3800).
7.
Connect the inhibitor switch connector (A).
8.
Install the shift cable by tightening nut (B).
   
   
Lightly tighten the shift cable mounting nut (B) so that necessary adjustments can be made.


9.
Push the shift cable to the arrow "F" to eliminate free play and then tighten the nut (A) with the specified torque.

Tightening torque :
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)


10.
Install the tray (A).

Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)


11.
Install the hybrid power control unit assembly.
( Refer to Hybrid Control System - "HPCU (Hybrid Power Control Unit)")
12.
Install the air cleaner assembly.
(1)
Disconnect the breather hose (A).
(2)
Disconnect the air intake hose (B) and then remove the air cleaner assembly (C).

Tightening torque:
Hose clamp bolt:
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)
Air cleaner assembly bolts:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)


   
   
When installing the air intake hose, the plate of the hose clamp must be in line with the stopper of the hose.
When installing the air intake hose, the center of the mark of hose must be in line with the throttle body rib.


13.
Install the air duct (A).

Tightening torque :
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)


14.
Install the under cover (A).

Tightening torque:
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)


15.
Connect the high voltage circuit.
16.
Refill the hybrid motor cooling system with coolant and then perform the air bleeding using the GDS.
(Refer to Hybrid Motor System - "Coolant")
Inhibitor Switch Schematic Diagrams
Circuit Diagram ...

Shift Lever Components and Components Location
Components 1. Shift lever assembly 2. Shift cable retainer3. Shift cable assembly4. "P" position switch5. Manual mode switch housing6. Shift lock solenoid ...

See also:

Compass Mirror Description and Operation
Function 1. Push the A button lower of the rear view mirror to turn on the function of the compass mirror so that displays a sign of a direction on the small board in the upper-right side of t ...

Mode Selection
Controls the direction of air flow through the ventilation system. The air from outlet port flows at any mode. Close the ventilation outlets using the knob to block the air flow if you do not wan ...

Components Operations
PCM (Power Train Control Module) 1. The PCM(ECM) (A) carries out a check of the ignition key using a special encryption algorithm, which is programmed into the transponder as well as ...

Copyright www.kiopman.com 2021