Kia Optima: Hood Repair procedures - Exterior - Body (Interior and Exterior)Kia Optima: Hood Repair procedures

Replacement
Hood Assembly Replacement
   
   
When removing and installing the hood, an assistant is necessary.
Be careful not to damage the hood and body.
When removing the clips, use a clip remover.
1.
Using a screwdriver, lift the socket clips (A) up slightly on both ends of the lifter (B).


2.
After loosening the hood hinge (A) mounting bolts, remove the hood panel (B).

Tightening torque :
21.6~26.5 N.m (2.2~2.7 kgf.m, 15.9~19.5 lb-ft)


3.
Installation is the reverse of removal.
   
   
Make sure the hood locks/unlocks and opens/closes properly.
Adjust the hood alignment.
Hood Insulator Pad Replacement
1.
Using a clip remover, detach the clips, and remove the hood insulator pad (A).
   
   
Be careful not to scratch the hood panel.


2.
Installation is the reverse of removal.
   
   
Replace any damaged clips.
Hood Lift Replacement
1.
Using a screwdriver (A), lift the socket clips (B) up slightly on both ends of the lifter (C), and then remove the lifter from the bracket (D).


2.
Installation is the reverse of removal.
Hood Seal Weatherstrip Replacement
1.
Detach the clips, then remove the hood seal weatherstrip (A).
   
   
Be careful not to scratch the hood seal weatherstrip.


2.
Installation is the reverse of removal.
   
   
Replace any damaged clips.
Hood Weatherstrip Replacement
1.
Remove the hood weatherstrip (A).


2.
Installation is the reverse of removal.
Hood Release Handle Replacement
1.
Using a screwdriver or remover, remove the hood release handle (A).


2.
Installation is the reverse of removal.
   
   
Make sure the hood latch cable is connected properly.
Make sure the hood locks/unlocks and opens/closes properly.
Hood Latch Replacement
1.
After loosening the mounting clips and bolts, then remove the rediator upper cover (A).


2.
Detach the clips, then remove hood latch cover (A).


3.
Remove the hood latch (A) mounting bolts.

Tightening torque :
7.8 ~ 11.8N.m (0.8 ~ 1.2kgf.m, 5.8 ~ 8.7 lb-ft)


4.
Disconnect the hood latch cable (A) and remove the hood latch (B).


5.
Installation is the reverse of removal.
   
   
Make sure the hood latch release cable is connected properly.
Make sure the hood locks/unlocks and opens/closes properly.
Adjust the latch alignment.
Adjustment
Adjust Hood
1.
After loosening the hinge (A) mounting bolt, adjust the hood (B) by moving it up or down, or right or left.
2.
Adjust the hood height by turning the hood overslam bumpers (C).
3.
After loosening the hood latch (D) mounting bolts, adjust the latch by moving it up or down, or right or left.


Fender Repair procedures
Replacement     • Be careful not to damage the fender and body. • When removing the clips, use a clip remover. 1. Remove the front bumper. (Ref ...

Trunk Lid Repair procedures
Replacement Trunk Lid Assembly Replacement     • When removing and installing the trunk lid, an assistant is necessary. • Wear gloves to protect hands ...

See also:

Catalytic Converter. Description and Operation
Description The catalytic converter of the gasoline engine is a three way catalyst. It oxidizes carbon monoxide and hydrocarbons (HC), and separates oxygen from the oxides of nitrogen (NOx). ...

Power Window Switch Schematic Diagrams
Circuit Diagram Driver Power Window Switch (1) Driver Power Window Switch (2) [Auto Down] [Safety Up/Down] Passenger And Rear Power Window Switch Rear Power Window + Seat Heater Switch ...

Automatic heating and air conditioning
The automatic climate control system is controlled by simply setting the desired temperature. The Full Automatic Temperature Control (FATC) system automatically controls the heating and cooling ...

Copyright www.kiopman.com 2020