Kia Optima: Driver Airbag (DAB) Module and Clock Spring Repair procedures - Airbag Module - RestraintKia Optima: Driver Airbag (DAB) Module and Clock Spring Repair procedures

Removal
1.
Set the front tires straight-ahead before removing the steering wheel.
   
   
If the steering wheel and the front tires are not set straight ahead together, it affects the number of circulation of steering wheel and the cable inside the clock spring is possible to be damaged.
2.
Disconnect the battery negative cable.
   
   
After disconnecting the battery negative cable, wait for at least thirty seconds.
3.
Remove the driver airbag module from the steering wheel after pressing the snap fit pin stopper.


4.
Remove the wiring fixing clip(C) and disconnect the horn connector (A).


5.
Release the connector locking pin, then disconnect the driver airbag module connector(B).
   
   
The removed airbag module should be stored in a clean, dry place with the pad cover facing up.
6.
Remove the steering wheel and steering wheel column shroud. (Refer to the Steering System group- Steering Column and Shaft)


7.
Disconnect the clock spring and horn connector, then remove the clock spring.

Inspection


Inspection
Driver Airbag (DAB)
If any improper parts are found during the following inspection, replace the airbag module with a new one.
   
   
Never attempt to measure the circuit resistance of the airbag module (squib) even if you are using the specified tester. If the circuit resistance is measured with a tester, accidental airbag deployment will result in serious personal injury.
1.
Check pad cover for dents, cracks or deformities.
2.
Check the airbag module for denting, cracking or deformation.
3.
Check hooks and connectors for damage, terminals for deformities, and harness for binds.
4.
Check airbag inflator case for dents, cracks or deformities.


5.
Install the airbag module to the steering wheel to check for fit or alignment with the wheel.
Clock Spring
1.
If, as a result of the following checks, even one abnormal point is discovered, replace the clock spring with a new one.
2.
Check connectors and protective tube for damage, and terminals for deformities.

Installation


Installation
1.
Set the front tires straight-ahead before assembling the steering wheel.
   
   
If the steering wheel and the front tires are not set straight ahead together, it affects the number of revolutions of steering wheel and the cable inside the clock spring is possible to be damaged.
2.
Disconnect the battery negative cable.
   
   
After disconnecting the battery negative cable, wait for at least thirty seconds.
3.
Set the clock spring in center before assembling it to a steering wheel.
(1)
Turn the clock spring clockwise or counter clockwise until it is locked in center automatically with sound of click.


(2)
Check the orange indicater in the clock spring.


4.
Connect the clock spring harness connector and horn harness connector to the clock spring.
5.
nstall the steering wheel column cover and the steering wheel. (Refer to the Steering System group- Steering Column and Shaft)
6.
Connect the Driver Airbag (DAB) module connector, and then install the Driver Airbag (DAB) module on the steering wheel.
7.
Connect the battery negative cable.
8.
After installing the airbag, confirm proper system operation.
   
   
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
Make sure horn works.
Driver Airbag (DAB) Module and Clock Spring Components and Components Location
Components 1. Driver Airbag (DAB)2. Steering Wheel3. Clock Spring ...

Passenger Airbag (PAB) Module Description and Operation
Description The passenger airbag (PAB) is installed inside the crash pad and protects the front passenger in the event of a frontal crash. The SRSCM determines if and when to deploy the PAB. ...

See also:

Cruise Control Switch Repair procedures
Removal and Installation 1. Disconnect the battery negative terminal. Tightening torque : 4.0 ~ 6.0N.m (0.4 ~ 0.6kgf.m, 3.0 ~ 4.4lb-ft) 2. Remove the driver airbag module. (Refer to the ...

Reprogramming a Single HomeLink Button
To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do not release until step 4 has been completed. 2. ...

Brake Actuation Unit Repair procedures
Removal 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the air duct (A). 3. Remove air cleaner assembly (B). 4. Disconnect the brake fluid l ...

Copyright www.kiopman.com 2021