Kia Optima: Body Side Moulding Repair procedures - Exterior - Body (Interior and Exterior)Kia Optima: Body Side Moulding Repair procedures

Replacement
Roof Moulding Replacement
   
   
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Take care not to scratch the body surface.
1.
Using a screwdriver or remover, remove the roof moulding (A).


2.
Installation is the reverse of removal.
   
   
Replace any damaged clips.
Fender Garnish Replacement
   
   
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Take care not to scratch the body surface.
1.
Using a screwdriver or remover, remove the fender garnish (A).


2.
Installation is the reverse of removal.
   
   
Replace any damaged clips.
C Pillar Moulding Replacement
   
   
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Take care not to scratch the body surface.
1.
Using a screwdriver or remover, remove the C pillar moulding (A).


2.
Installation is the reverse of removal.
   
   
Replace any damaged clips.
Front Wheel Guard And Mud Guard Replacement
   
   
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged
Put on gloves to protect your hands.
Take care not to scratch the body surface.
1.
Remove the front tire.
2.
After loosening the mounting clips and screws, then remove the front wheel guard (A), mud guard (B).


3.
Installation is the reverse of removal.
   
   
Replace any damaged clips.
Rear Wheel Guard And Mud Guard Replacement
   
   
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damaged
Put on gloves to protect your hands.
Take care not to scratch the body surface.
1.
Remove the rear tire.
2.
After loosening the mounting clips and nut, then remove the rear wheel guard (A) and mud guard (B)
[RH]

[LH]


[LH]


3.
Installation is the reverse of removal.
   
   
Replace any damaged clips.
Side Sill Moulding Replacement
   
   
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Take care not to scratch the body surface.
1.
Loosen the mounting screws.
2.
Using a screwdriver or remover, remove the side sill moulding (A).
3.
Installation is the reverse of removal.
   
   
Replace any damaged clips


Rear Door Repair procedures
Replacement Door Trim Replacement     • Be careful not to scratch the door trim and other parts. • Put on gloves to protect your hands. 1. After ...

Panoramaroof Components and Components Location
Components 1. Roof moulding [RH]2. Roof moulding [LH]3. Movable glass4. Cover [RH]5. Wind deflector assembly6. Front cover assembly7. Panoramaroof frame assembly8. Cover [LH]9. Shield cover10. Wi ...

See also:

Air Flow Control (Mode Switch)
The mode selection button controls the direction of the air flow through the ventilation system. The air flow outlet port is same as manual climate control system. Face position Air flow is dir ...

Rear parking assist system
The rear parking assist system assists the driver during backward movement of the vehicle by chiming if any object is sensed within a distance of 120 cm (47 in.) behind the vehicle. This system ...

Check spark plugs and ignition system
Inspect your spark plugs as described in section 7 and replace them if necessary. Also check all ignition wiring and components to be sure they are not cracked, worn or damaged in any way. ...

Copyright www.kiopman.com 2020